BLOG
Bring you the latest information inside and outside the industry, and hope to help you
How to do well in the maintenance of CNC hydraulic press
Release time:
Jun 13,2022
Source:
Proper use of numerical control hydraulic press, careful maintenance and strict implementation of safety operation rules are the main conditions for prolonging the service life of equipment and ensuring safe production
Correct use of CNC hydraulic press, careful maintenance and strict implementation of safety operation procedures are the main conditions for prolonging the service life of equipment and ensuring safe production. Therefore, besides being familiar with the structure and performance of the machine, the operator should also pay attention to the following points.
1. The commissioning and maintenance of the equipment requires personnel. When disassembling the hydraulic components, the components should be placed in a clean place, and the sealing surfaces should not be scratched.
2. The hydraulic oil is the energy transmission medium when the equipment is working. The quality, cleanliness and viscosity of the hydraulic oil play a major role in the life of the hydraulic pump, hydraulic valve and hydraulic cylinder. Therefore, attention should be paid to the quality of the hydraulic oil and the cleanliness of the hydraulic oil when using the hydraulic station. The oil used in the system shall be strictly filtered, and the system shall be equipped with an oil filter.
3. Under the condition of ensuring the normal operation of the CNC hydraulic press system, the pressure of the hydraulic pump should be adjusted as low as possible, and the pressure of the back pressure valve should also be adjusted as low as possible to reduce energy consumption and heat generation.
4. In order to prevent dust and water from falling into the oil, the oil tank shall be kept clean and maintained regularly.
5. The liquid level of the equipment oil tank shall always be kept high, so that the oil in the system has sufficient circulating cooling conditions, and pay attention to keeping the oil tank, pipeline and other equipment clean, so as to facilitate heat dissipation. Generally, the safe temperature of oil is 30 ℃ - 55 ℃, which is a more appropriate service temperature, with high performance and long service life. When the oil temperature is higher than 60 ℃, its service life will be reduced for every 8 ℃ increase.
6. The pressure in the CNC hydraulic press system shall not be lower than the atmospheric pressure as much as possible. At the same time, a good sealing device shall be used. If the seal fails, it shall be replaced in time. The stressed screws, such as the cylinder port guide sleeve screws and piston rod flange screws, shall be fastened regularly to avoid loosening. Avoid air entering the hydraulic system and oil leakage.
Next page
Related News
Introduction to composition and structure of servo hydraulic press system
Servo hydraulic machine system mainly includes main oil pump, hydraulic oil tank, filter, pressure reducing valve, overflow valve, lifting hydraulic cylinder, elastic hydraulic cylinder, tong hydraulic cylinder, outrigger hydraulic cylinder, hydraulic motor and various hydraulic operation valves. Before the equipment leaves the factory, the pressure of the overflow valve, pressure reducing valve and various pressure valves has been set to ensure the safe operation of the equipment system. The user shall not change easily when using.
Reasons for no oiling or insufficient output of CNC hydraulic press
The slide wedge of numerical control hydraulic press is too tight, and the movement of eccentric mechanism is blocked greatly. The sliding block shall be kept with proper clearance to make it move flexibly.
Talk about the harm of high temperature of servo hydraulic press
1. The high body temperature of the servo hydraulic press will reduce the viscosity of the oil, increase the leakage, reduce the efficiency of the system and the volume base efficiency of the pump, while the oil film of moving parts such as slide valves will become thinner, resulting in greater friction resistance, which will lead to increased wear and affect the normal operation of the machine.
Explain the causes of vibration of CNC hydraulic press
Due to its tonnage, the CNC hydraulic press will not shake during use, so when encountering shaking, stop working, check the reasons, and remember not to be careless.
What needs to be done before starting the servo hydraulic press
Servo hydraulic press is a kind of energy saving and high efficiency hydraulic press that uses servo motor to drive the main transmission oil pump, reduce the control valve circuit and control the hydraulic press slider. Suitable for stamping, die forging, press fitting, straightening and other processes.
How to do well in the maintenance of CNC hydraulic press
Proper use of numerical control hydraulic press, careful maintenance and strict implementation of safety operation rules are the main conditions for prolonging the service life of equipment and ensuring safe production